Roofing Material Calculator

Work out the sloped area of a roof and how much roofing to buy: shingle bundles, packages or tiles, underlayment rolls, and ridge, starter and drip edge pieces. Enter the building footprint and pitch, measure each roof plane, or start from a known roof area. Every material uses the coverage from its package, and the pitch factor is shown with your numbers.

Units
Input mode
Building

Feet: 40.5 or 40' 6"

Roof type

Eave and gable overhang beyond the walls.

6:12 = 26.6° = 50%. Up to 24:12 (63.4°).

Roofing material

Use more for hips, valleys and complex roofs.

Usually 3 for three-tab and many architectural shingles; check the wrapper.

Net coverage after overlaps, from the roll label. Leave empty to skip.

Ridge and edges (optional)

Estimate from the footprint: 42 ft

Estimate from the footprint: 84 ft

Estimate from the footprint: 71.6 ft

Prices (optional)

Result

Bundles to buy50
Roof area1,502.64 sq ft
Result
Footprint incl. overhang1,344 sq ft
Pitch factor1.118
Roof area1,502.64 sq ft
Roofing squares15.03
Squares including 10% waste16.53
Roof area including waste1,652.9 sq ft
Bundles to buy50
Coverage of what you buy1,666.67 sq ft

Calculation settings

  • Units: US (ft, in) · Input mode: Footprint and pitch
  • Gable (two slopes): 40 × 30 ft, overhang (each side) 12 in, roof pitch 6:12
  • Waste allowance: 10% · Bundles per square (shingles)

How this was calculated

  1. Footprint incl. overhang(40 + 2 × 1) × (30 + 2 × 1) = 1,344 sq ft
  2. Pitch factor√(1 + 0.5²) = 1.118 (6:12)
  3. Roof area1,344 × 1.118 = 1,502.64 sq ft
Show all 5 steps
  1. Roofing squares incl. waste1,502.64 sq ft ÷ 100 × 1.1 = 16.53
  2. Main materialround up(16.53 × 3) = 50

This calculator covers roof geometry and material quantities only. It does not design rafters or trusses, check loads, or confirm code compliance. Before re-roofing, have the deck and local requirements checked by a licensed professional.

Enter the building footprint and pitch, measure each roof plane, or start from a known roof area. Every material uses the coverage from its package, and the pitch factor is shown with your numbers.

How to use the roofing calculator

  1. Choose how to enter the roof: footprint and pitch, individual planes, or a known area.
  2. For the footprint, enter the building length, width, overhang and pitch (as rise in 12, degrees or percent).
  3. Set the waste allowance — more for hips, valleys and dormers.
  4. Choose how your roofing is sold and enter its coverage from the package.
  5. Optionally add underlayment, ridge, eave and rake lengths, and prices.

Roof pitch factor

A sloped roof covers more area than the footprint under it. The pitch factor is √(1 + (rise ÷ run)²); multiply the footprint by it to get the roof area.

PitchDegreesPitch factor
3:1214.0°1.031
4:1218.4°1.054
6:1226.6°1.118
8:1233.7°1.202
10:1239.8°1.302
12:1245.0°1.414

Roofing squares and bundles

A roofing square is 100 sq ft of roof. Many shingles come three bundles to the square, but some heavy architectural shingles use four or five — always check the wrapper. Bitumen shingles in Europe are usually sold by the package with the coverage printed on it, and clay or concrete tiles by pieces per square metre.

Measuring roof planes

For each plane, measure the length along the eave and the slope length from the eave edge to the ridge. Multiply them for the plane area. Measuring planes directly is more accurate than the footprint method for roofs with dormers or different pitches.

Safety limits

This page does not ask for span, timber grade, snow or wind loads because it does not design the roof structure. For structural questions, and whenever you are unsure about the condition of the deck, consult a licensed roofer or engineer.

Roofing calculator formulas

Pitch factor
√(1 + (rise ÷ run)²)
Footprint
(building length + 2 × overhang) × (building width + 2 × overhang)
Roof area
footprint × pitch factor, or sum(plane length × slope length)
Roofing squares
roof area ÷ 100 sq ft
Bundles
round up(squares × (1 + waste % ÷ 100) × bundles per square)
Packages
round up(roof area × (1 + waste % ÷ 100) ÷ coverage per package)
Underlayment rolls
round up(roof area × (1 + waste % ÷ 100) ÷ net coverage per roll)
Linear materials
round up(length × (1 + linear waste % ÷ 100) ÷ coverage per unit)

Worked example

  1. A 40 × 30 ft building with no overhang: footprint = 1,200 sq ft.
  2. Pitch 6:12: factor = √(1 + 0.5²) = 1.118.
  3. Roof area = 1,200 × 1.118 = 1,341.6 sq ft = 13.42 squares.
  4. 10% waste: 13.42 × 1.10 = 14.76 squares.
  5. 3 bundles per square: 14.76 × 3 = 44.27, rounded up to 45 bundles.

Assumptions

  • Footprint mode assumes a simple gable or shed roof with the same pitch on every plane.
  • Hips, valleys, dormers and complex shapes are covered by the waste allowance or by measuring planes.
  • Material counts use only the coverage you enter from the package.
  • Starter is counted along the eaves; drip edge along eaves and rakes.
  • This is a material estimate, not a structural design.

Frequently asked questions

How do I calculate roof area from the footprint?

Add the overhang to each side of the building, multiply length by width, then multiply by the pitch factor √(1 + (rise ÷ run)²). A 6:12 roof has a factor of about 1.118.

How many bundles of shingles are in a square?

Usually three bundles cover one square (100 sq ft), but some heavy architectural shingles need four or five. The calculator uses whatever number you enter from the wrapper.

How much waste should I add for roofing?

About 10% for a simple gable roof. Hips, valleys and dormers create more cutting, so 15% or more is common on complex roofs.

How do I convert roof pitch to degrees?

Degrees = arctan(rise ÷ run). 4:12 is about 18.4°, 6:12 about 26.6° and 12:12 exactly 45°. Choose degrees or percent in the calculator to enter pitch that way.

Does the calculator work for metal roofing or clay tiles?

Yes, as long as you count by coverage per package or pieces per area from the manufacturer. Metal sheet layouts with fixed lengths need a supplier's take-off for an exact order.

Can this calculator size rafters or trusses?

No. It deliberately covers geometry and materials only. Structural members depend on span, loads and local codes and must be designed by a qualified professional.