Gravel Calculator

Find out how much gravel to order in cubic yards, cubic meters, tons or bags. Add one or more areas — rectangles, circles, rings, trenches or a known area — enter the depth, and choose a material. Compaction and waste are separate allowances, density is visible and editable, and bags or truckloads appear only when you enter their size.

Units

Choosing a project suggests a typical depth and material; anything you changed stays.

Areas to cover

Add one row per area; each can have its own shape. Feet: 10.5 or 10' 6"

Area 1
Material

Typical: 2–3 in for paths and beds, 4–6 in for a driveway top layer.

Typical estimate; varies 1.26–1.52 tons/cu yd with size, moisture and supplier. Use your supplier's figure if you have it.

Extra for material that settles when compacted, e.g. 10–15 % for a driveway base.

Spillage and uneven ground.

Bags, loads and price (optional)
Bag size by

Result

Volume to order0.65 cu yd
Weight0.91 tons
Result
Area100 sq ft
Volume before allowances16.67 cu ft · 0.617 cu yd
Volume with 0% compaction and 5% waste0.648 cu yd · 0.496 m³
Weight0.91 tons · 0.82 t
Weight (lb)1,815
Weight range0.82–0.98 tons

Weight uses a typical density. Ask your supplier for the figure for their material.

Calculation settings

  • Units: US (ft, in) · Project: General
  • Area 1: Rectangle — 10 × 10
  • Depth: 2 in · Gravel (general): 1.4 tons/cu yd · Compaction allowance: 0% · Waste allowance: 5%

How this was calculated

  1. Area10 × 10 = 100 sq ft
  2. Volume100 × 0.1667 ft = 16.667 cu ft
  3. Adjusted volume0.617 × 1 × 1.05 = 0.648 cu yd
Show all 4 steps
  1. Weight0.648 × 1.4 = 0.907 tons

Compaction and waste are separate allowances, density is visible and editable, and bags or truckloads appear only when you enter their size.

How to use the gravel calculator

  1. Pick a project type to get a typical depth and material, or keep General.
  2. Add each area with its shape and measurements.
  3. Enter the depth of the gravel layer.
  4. Check the material density — replace it with your supplier's figure if you have one.
  5. Set compaction and waste, then optionally add bag size, truck capacity and price.

Gravel depth

Most decorative beds and paths need 2–3 in of gravel. A driveway top layer is usually 4–6 in over a compacted base, and a French drain trench is often 12–24 in deep. For deeper jobs, calculate each layer separately with its own material.

UseTypical depthCommon material
Garden beds, mulch replacement2–3 in (5–8 cm)River rock, decorative
Paths and patios2–3 in (5–8 cm)Pea gravel
Driveway top layer4–6 in (10–15 cm)Crushed stone
Driveway base4–8 in (10–20 cm)Crushed stone with fines
French drain12–24 in (30–60 cm)Washed crushed stone

Density and weight

Gravel is sold by volume (cubic yards or cubic meters) or by weight (tons or tonnes). Converting between them needs the bulk density, which depends on stone size, shape, moisture and supplier. A common rule of thumb is about 1.4 US tons per cubic yard (about 1.66 t/m³), but always prefer your supplier's figure.

Compaction

Crushed stone with fines settles noticeably when compacted, so you need more loose material than the finished volume. The compaction allowance is applied separately from waste so you can see why the order grows.

Bags versus bulk

Bags are convenient for small jobs; bulk delivery is usually cheaper above about one cubic yard. The calculator shows bags and truckloads only when you enter their size, because both vary by store and supplier.

Gravel calculator formulas

Rectangle
length × width
Circle
π × radius²
Ring
π × (outer radius² − inner radius²)
Trench
trench length × trench width
Volume
total area × depth
Adjusted volume
volume × (1 + compaction % ÷ 100) × (1 + waste % ÷ 100)
Weight
adjusted volume × bulk density
Bags
round up(weight ÷ bag weight) or round up(volume ÷ bag volume)
Loads
round up(weight or volume ÷ load capacity)

Worked example

  1. A 10 × 10 ft area at 3 in deep: 100 sq ft × 0.25 ft = 25 cu ft = 0.926 cu yd.
  2. 5% waste: 0.926 × 1.05 = 0.972 cu yd.
  3. At 1.4 tons per cu yd: 0.972 × 1.4 = 1.36 tons (about 2,722 lb).
  4. In 50 lb bags: 2,722 ÷ 50 = 54.4, rounded up to 55 bags.

Assumptions

  • Depth is the same across all areas.
  • Densities are typical loose bulk densities; real material varies.
  • Compaction and waste are separate multipliers.
  • Cost uses the exact quantity for bulk prices and whole bags for bag prices.
  • Bags and loads are counted only when you enter their size.

Frequently asked questions

How do I calculate how much gravel I need?

Multiply the area by the depth to get the volume, add allowances for compaction and waste, then multiply by the density to get the weight. The calculator does each step and shows the formula with your numbers.

How many tons of gravel are in a cubic yard?

Roughly 1.4 US tons for typical gravel, but it ranges from about 1.25 to 1.5 tons depending on stone size and moisture. Use your supplier's figure for an accurate order.

How many bags of gravel make a cubic yard?

A cubic yard of gravel weighs about 2,800 lb, so it takes around 56 bags of 50 lb, or 54 bags of 0.5 cu ft. Enter your bag size to get an exact count.

How deep should gravel be for a driveway?

Usually 4–6 in of crushed stone over a compacted base of 4–8 in. Soft ground or heavy vehicles need more; local practice varies.

How much gravel do I need for a French drain?

Choose the Trench shape, enter the trench length and width and the gravel depth. Subtract the volume of the pipe if you want a tighter estimate.

Should I add extra for compaction?

For crushed stone with fines that you will compact, add about 10–15 %. Washed stone and pea gravel barely compact, so 0–5 % is usually enough.