Drywall Calculator

Estimate how many drywall sheets to buy for a room, a set of walls and ceilings, or an area you already know — plus joint compound, tape and screws. Every consumable shows the rate it uses, and you can change it to match your product. Costs come only from the prices you enter.

Units
Input mode
Room

Feet: 12.5 or 12' 6"

Openings

Doors, windows and other areas that will not be covered.

Sheets

Extra for cuts around openings and damaged sheets.

Mud, tape and screws

Typical: a 4.5-gal pail of ready-mixed mud covers about 400 sq ft for three coats (≈ 11 gal per 1,000 sq ft). Check your product.

Printed on the roll.

Leave empty to use the estimate from the sheet layout.

Typical: about 1 screw per sq ft of board (32 per 4 × 8 ft sheet). Ceilings need more.

Prices (optional)

Result

Sheets to buy19
Pails of mud2
Tape rolls1
Result
Wall area384 sq ft
Ceiling area144 sq ft
Net area to cover528 sq ft
Sheets before waste16.5
Sheets including 10% waste19
Pails of mud2
Joint length198 ft (estimate)
Tape rolls1
Screws608

Hanging direction does not change the sheet count here; choose the layout that gives the fewest joints on site.

Calculation settings

  • Units: US (ft, in) · Input mode: Room
  • Room: 12 × 12 × 8 ft + ceiling area
  • Sheet size: 4 × 8 ft · Waste allowance: 10%
  • Coverage per pail of mud: 400 sq ft
  • Tape per roll: 500 ft
  • Screws per sheet: 32

How this was calculated

  1. Wall area2 × (12 + 12) × 8 = 384 sq ft
  2. Ceiling area12 × 12 = 144 sq ft
  3. Net area528 sq ft = 528 sq ft
Show all 10 steps
  1. Sheet area4 × 8 ft = 32 sq ft
  2. Sheets before waste528 ÷ 32 = 16.5
  3. Sheets to buyround up(16.5 × 1.1) = 19
  4. Compound unitsround up(580.8 sq ft ÷ 400 sq ft) = 2
  5. Joint length (estimate)528 × (4 + 8) ÷ 32 = 198 ft
  6. Tape rollsround up(198 ÷ 500) = 1
  7. Screws19 × 32 = 608

Planning estimate, not a cutting plan or a labour quote. Consumable rates are typical values; check the coverage printed on your products.

Every consumable shows the rate it uses, and you can change it to match your product. Costs come only from the prices you enter.

How to use the drywall calculator

  1. Choose how to enter the job: a whole room, individual walls and ceilings, or a known total area.
  2. Enter the dimensions and add doors and windows as openings.
  3. Pick the sheet size and a waste allowance.
  4. Check the mud, tape and screw rates against your products and change them if needed.
  5. Optionally enter prices to get a material cost per item and in total.

Drywall sheet sizes

SheetAreaTypical use
4 × 8 ft32 sq ftStandard walls; easy to carry
4 × 10 ft40 sq ftWalls up to 10 ft; fewer butt joints
4 × 12 ft48 sq ftLong walls and ceilings; fewest joints
1200 × 2500 mm3.0 m²Most common metric sheet
1250 × 2600 mm3.25 m²Common in Germany for 2.6 m walls

Longer sheets mean fewer joints to tape, but they are heavier and harder to handle in small rooms.

Mud and tape coverage

Joint tape follows the sheet edges. If every sheet contributes half of its perimeter, a 4 × 8 ft layout needs about 0.375 ft of joint per square foot of board — close to the 370 ft per 1,000 sq ft that USG publishes. The calculator uses this estimate unless you enter your actual joint length.

Compound use depends on the product and finish level. For a standard three-coat finish, ready-mixed mud is often estimated at about 11 gallons per 1,000 sq ft and powdered compound at about 80 lb (≈ 0.4 kg/m²). Change the coverage to the figure on your bag or pail.

Drywall calculator formulas

Wall area
2 × (room length + room width) × wall height
Ceiling area
room length × room width
Net area
wall area + ceiling area − openings
Sheets to buy
round up(net area ÷ sheet area × (1 + waste % ÷ 100))
Compound units
round up(net area × (1 + waste % ÷ 100) ÷ coverage per unit)
Tape rolls
round up(joint length ÷ tape per roll)
Screws
sheets to buy × screws per sheet

Worked example

  1. A 12 × 12 ft room with 8 ft walls: 2 × (12 + 12) × 8 = 384 sq ft of walls.
  2. 4 × 8 ft sheets = 32 sq ft each: 384 ÷ 32 = 12 sheets before waste.
  3. 10% waste: 12 × 1.10 = 13.2, rounded up to 14 sheets.
  4. Mud at 400 sq ft per pail: 384 × 1.10 = 422.4 sq ft ÷ 400 = 1.06, rounded up to 2 pails.
  5. Tape: 384 × 0.375 = 144 ft of joints, so one 500 ft roll.
  6. Screws: 14 sheets × 32 = 448 screws.

Assumptions

  • Surfaces and openings are treated as rectangles.
  • Sheets are counted by area; the calculator does not optimise a cutting plan.
  • Joint length is estimated from the sheet size unless you enter the actual length.
  • Mud, tape and screw rates are typical published values and can be changed.
  • Costs include only the prices you enter; labour is not included.

Frequently asked questions

How many sheets of drywall do I need for a 12 × 12 room?

With 8 ft walls the walls are 384 sq ft: 12 sheets of 4 × 8 ft before waste, 14 with 10% extra. Adding the ceiling (144 sq ft) brings it to 528 sq ft, or 19 sheets with 10% waste.

How much joint compound do I need?

For a three-coat finish, plan roughly 11 gallons of ready-mixed mud per 1,000 sq ft, or about 0.4 kg/m² of powdered compound. Smoother finish levels and skim coats need more.

How much drywall tape do I need?

About 370 ft per 1,000 sq ft of board for 4 × 8 sheets. Larger sheets mean fewer joints and less tape.

How many screws per sheet of drywall?

A common estimate is about one screw per square foot of board — 32 for a 4 × 8 ft sheet on walls. Ceilings and fire-rated assemblies use closer spacing; follow the board manufacturer's schedule.

How much extra drywall should I buy?

Around 10% for typical rooms. Use 15% or more for many openings, angled walls or small pieces you cannot reuse.

Does the calculator include labour cost?

No. It estimates materials and multiplies them by the prices you enter. Installation cost varies too much by location to estimate honestly.